3/32 DIN 875/I 4000 858 067 4000 858 061 DIN 875/00 INOX DIN 875/00 INOX DIN 875/00 INOX DIN 875/00 DIN 875/II D no stock item. Procurement takes place after receipt of order. a = delivery by carrier + = fraction of the PU possible You will find the explanation of the symbols before the index. Measuring instruments Leg L [mm] Cross section [mm] Article no. Without stop EUR CK Article no. With stop EUR CK 75 x 50 15 x 4 4000 858 061 8,25 PC24 4000 858 067 10,25 PC24 100 x 70 20 x 6 4000 858 062 9,75 PC24 4000 858 068 11,75 PC24 150 x 100 30 x 6 4000 858 063 14,25 PC24 4000 858 069 17,50 PC24 200 x 130 30 x 8 4000 858 064 18,75 PC24 4000 858 070 22,95 PC24 250 x 165 35 x 8 4000 858 065 22,95 PC24 4000 858 071 27,95 PC24 300 x 200 40 x 8 4000 858 066 31,95 PC24 4000 858 072 40,95 PC24 Bracket Precision design · Surface-hardened aluminium (HRc 62) · Black anodised · Suitable for testing and inspection work · With raised edge scale, mm partition With raised edge scale, mm partition Leg L [mm] Cross section [mm] Article no. EUR CK 50x 40 14 x 4,5 4000 858 385 29,95 PU12 75x 50 16 x 4 4000 858 386 31,95 PU12 100x 70 20 x 5 4000 858 387 38,95 PU12 150x100 28 x 6 4000 858 388 53,95 PU12 200x130 30 x 7 4000 858 389 65,95 PU12 Bevelled square Precision design · Flat type · Made of special steel · With finely ground and lapped straight-edge · Suitable for inspection and measuring room Length of handle [mm] Straight-edge [mm] Article no. EUR CK 40x22x10 60x4x4 4000 858 415 119,00 PU12 Bevelled square Adjustable · High-precision base unit with sliding straight-edge · Straight-edge infinitely adjustable and lockable via clamping spindle · Measuring surfaces ground and lapped · Bracket fully hardened Use: for test work with the light gap method · Allows the identification of minute deviations · The moveable straight-edge also enables testing operations to be carried out on short chamfered recesses, punches, etc. · Especially suitable for tool and mould making Leg L [mm] Cross section [mm] Article no. EUR CK 25x20 6 x 3,5 / 5 x 3,5 4000 858 403 17,95 ZR00 40x28 8 x 3,5 / 5 x 3,5 4000 858 404 17,95 ZR00 Square with inside bevelled edges Precision design · Hardened · With an internal straight-edge · Raised edges and flat surfaces accurately and finely ground · Test surfaces lapped Contents Article no. EUR CK 5-part 4000 851 162 159,00 PE07 Test set Comprising: 1 bevelled square 75 x 50 mm 1 square with inside bevelled edges each of size 40 x 28 mm and 25 x 20 mm 1 straight-edge 100 mm 1 gauge block marking tip 60 x 8 x 8 mm Leg L [mm] Cross section [mm] Article no. EUR CK 120x 80 20 x 5 4000 858 400 21,95 PC24 150x100 20 x 5 4000 858 401 24,95 PC24 200x130 25 x 5 4000 858 402 32,95 PC24 Bevel angle 135° · With stop · Made of steel · With high-precision raised edges and perfectly machined flat sides For precise marking and checking of 45° for corner bonding 90° Leg L [mm] Cross section [mm] Article no. EUR CK 100x 70 90 4000 858 031 35,95 PU12 150x130 190 4000 858 032 44,95 PU12 200x150 220 4000 858 033 55,95 PU12 250x160 230 4000 858 034 72,95 PU12 300x180 280 4000 858 035 96,95 PU12 Centre squares Precision design · Surface-hardened aluminium (HRC 62), black anodised · With mm partition for centring round panels and shafts Factory standard
RkJQdWJsaXNoZXIy ODY1MjQ=