2/37 b1 h1 l D [mm] D1 [mm] H [mm] Spigot Ø [mm] Article no. EUR CK 65 min. 22 mm / max. 100 30 12 4000 833 137 49,95 ZX02 Screw jack support Nr. 6441 V-block · Suitable for screw jacks with 12 mm centring hole · Tempered steel · Tempered and burnished T-slot [mm] b1 [mm] h1 [mm] H max. [mm] l [mm] Article no. EUR CK 12/14/16/18 19 38 99 179 4000 833 184 319,00 ZX02 Extra strong clamping jaw Nr. 6497 Reversible clamping jaws · High design with precise prism guide · Base unit made of malleable cast iron · Clamping jaws, hardened steel, casehardened · With smooth side for machined work pieces and corrugated side for raw clamping surfaces Application: Thanks to the large clamping area, these sturdy clamping jaws are suitable for the lateral clamping of high work pieces. The use of two clamping bolts is recommended for attachment of the stabiliser jaw to the machine table. Depending on the groove width, screws for T-slots (DIN 787) - two pc. per clamping jaws - must be ordered separately as mounting screws. Supply without mounting screws Unless otherwise stated, delivery without content/ accessories. The offers are only valid for commercial customers. All prices excluding VAT. Clamping devices T-sliding block DIN 508 Tempered · Strength class 10 · Full load-bearing capacity of the nut for T-slots can only be achieved if the screw connection is across the entire thread length (DIN 508) factory standard: 4000 603 160, 4000 603 161, 4000 603 162, 4000 603 163, 4000 603 164, 4000 603 165, 4000 603 166, 4000 603 167, 4000 603 168, 4000 603 169, 4000 603 170, 4000 603 171, 4000 603 172, 4000 603 173, 4000 603 174, 4000 603 175, 4000 603 177, 4000 833 205, 4000 833 206, 4000 833 208, 4000 833 209, 4000 833 211, 4000 833 212, 4000 833 214, 4000 833 215 Thread T-slot [mm] A [mm] E [mm] H [mm] K [mm] Article no. EUR CK Thread T-slot [mm] A [mm] E [mm] H [mm] K [mm] Article no. EUR CK M5 6 5.7 10 8 4 4000 833 200 2,75 ZX02 M12 18 17.7 28 20 10 4000 603 168 5,75 ZX02 M6 8 7.7 13 10 6 4000 833 201 2,20 ZX02 M14 18 17.7 28 20 10 4000 833 206 4,95 ZX02 M8 10 9.7 15 12 6 4000 833 202 2,30 ZX02 M16 18 17.7 28 20 10 4000 833 207 4,25 ZX02 M8 12 11.7 18 14 7 4000 603 160 3,45 ZX02 M16 20 19.7 32 24 12 4000 833 208 6,95 ZX02 M10 12 11.7 18 14 7 4000 833 203 2,30 ZX02 M16 22 21.7 35 28 14 4000 603 169 9,95 ZX02 M8 14 13.7 22 16 8 4000 603 161 3,75 ZX02 M20 22 21.7 35 28 14 4000 833 210 6,95 ZX02 M10 14 13.7 22 16 8 4000 603 162 3,75 ZX02 M20 24 23.7 40 32 16 4000 833 211 13,25 ZX02 M12 14 13.7 22 16 8 4000 833 204 2,75 ZX02 M16 28 27.7 44 36 18 4000 603 172 17,25 ZX02 M12 16 15.7 25 18 9 4000 603 165 4,50 ZX02 M20 28 27.7 44 36 18 4000 603 173 17,95 ZX02 M14 16 15.7 25 18 9 4000 833 205 3,55 ZX02 M24 28 27.7 44 36 18 4000 833 213 13,25 ZX02 M10 18 17.7 28 20 10 4000 603 167 6,25 ZX02 M30 36 35.6 54 44 22 4000 603 176 27,95 ZX02 T-sliding block Nr. 510 Rhombic · Tempered · Because of the reduced contact surface in the T-slots, the load-bearing capacity is lower than for the comparable sizes DIN 508 Particular product benefits: Rhomboid sliding blocks can be inserted into the T-slots from above. Especially useful for long T-slots or when the occupancy of the machine table layout does not allow for the insertion of clamping bolts or sliding blocks from the side Thread T-slot [mm] A [mm] E [mm] H [mm] K [mm] Article no. EUR CK Thread T-slot [mm] A [mm] E [mm] H [mm] K [mm] Article no. EUR CK M8 10 9.7 15 12 6 4000 603 182 5,95 ZX02 M16 22 21.7 35 28 14 4000 603 185 16,95 ZX02 M12 14 13.7 22 16 8 4000 833 217 7,50 ZX02 M20 22 21.7 35 28 14 4000 833 222 13,50 ZX02 M16 18 17.7 28 20 10 4000 833 219 8,75 ZX02 M24 28 27.7 44 36 18 4000 833 223 22,95 ZX02
RkJQdWJsaXNoZXIy ODY1MjQ=