Grinding disc Ø [mm] 125 Nominal input power [W] 800 No-load speed [min-¹] 11800 Grinding spindle M14 Mains voltage 230 V / 50 Hz Weight [kg] 1.8 Article no. 8000 149 880 EUR 85,95 CK MJ15 Angle grinder DWE 4057 Very low housing diameter · Epoxy resin armoured coil · Re-start protection and safety switch · Soft start · Cut-off carbon brushes · Spindle catch Scope of supply: Clamping nut, clamping flange, additional handle, protective hood, assembly tool Grinding disc Ø [mm] 230 Nominal input power [W] 2600 No-load speed [min-¹] 6500 Grinding spindle M14 Mains voltage 230 V / 50 Hz Weight [kg] 5.4 Article no. 8000 593 691 EUR 172,00 CK MJ15 Angle grinder DWE 496 Epoxy resin armoured coil · Re-start protection and safety switch · Soft start · Locking switch for continuous operation · Spindle catch Scope of supply: Clamping nut, clamping flange, additional handle, protective hood Grinding disc Ø [mm] 125 Oscillating circuit [mm] 2.6 Nominal input power [W] 280 Oscillation rate [min-¹] 8000–12000 Mains voltage 230 V / 50 Hz Weight [kg] 1.3 Article no. 8000 149 913 EUR 125,00 CK MR19 Eccentric grinder DWE 6423 Perform & Protect: extremely low vibrations and effective dust extraction, AirLock-compatible · Switches and gearbox housing, dust-protected · Soft start and revolution speed stabilisation Scope of supply: Dust collector Hub [mm] 40 Cutting L [mm] 430 Nominal input power [W] 1700 No-load speed [min-¹] 3000 Mains voltage 230 V / 50 Hz Weight [kg] 5.5 Article no. 4681 716 031 EUR 515,00 CK MR19 Special saw DWE 397 High-performance motor · Low-vibration and non-rebound double-saw blade system with quick stop in 3 seconds · Quick change system · Torsion-resistant blade · Suitable for angle cuts · Integrated end terminal · Fully rubberised handle · Ideal for sawing vertically perforated bricks with a strength class of up to 12 N/mm² Scope of supply: Carbide saw blade set DT2974, saw blade protector, Allen key Model DT 2974 Length of sheet [mm] 430 Article no. 4681 716 033 EUR 85,95 CK MR19 Special saw blade DT 2974 For easy cuts in vertically perforated bricks (Poroton) for a strength class of up to 12 N/mm² D no stock item. Procurement takes place after receipt of order. a = delivery by carrier + = fraction of the PU possible You will find the explanation of the symbols before the index. Power tools and compressed air tools Drilling power in concrete [mm] 26 Drilling power in steel [mm] 13 Drilling power in soft wood [mm] 30 Nominal input power [W] 800 No-load speed [min-¹] 0–1500 Stroke frequency [min-¹] 0–5500 Single stroke energy [J] 2.6 Tool holders SDS-plus Mains voltage 230 V / 50 Hz Weight [kg] 2.6 Article no. 8000 147 423 EUR 145,00 CK MR19 Drill and chipping hammer D 25133 K Fully-synchronised gears · Electronic Turning and stroke regulation · Turning and stroke stop · Large-scale switch · Safety coupling · Switchable carbon brushes Scope of supply: Rubber-coated additional handle, drill depth stop, T-STAK box 12/8 Ø 125 Ø 230 Ø 125 SDS plus
RkJQdWJsaXNoZXIy ODY1MjQ=