1/106 DIN 1835-B 10° Z 6-14 Typ N DIN 850D HSSCo DIN 1835-B 10° Z 6-10 Typ N DIN 851AB HSSCo D no stock item. Procurement takes place after receipt of order. a = delivery by carrier + = fraction of the PU possible You will find the explanation of the symbols before the index. Cutting tools Slot cutter HSS-Co · DIN 850 D · Type N · For milling structural steels, case-hardened steels, and tempered steels, as well as shortchipping non-ferrous metals · Straight shank with pulling face Cutting values, see Table 13 on Page 1/121 P M K N S H K Uncoated k K K K Nominal Ø d1 [mm] Cutting edge L b [mm] Overall L I1 [mm] Shank Ø d2 [mm] No. of cutters For grooves according to DIN 6888 [mm] Article no. EUR CK 4.5 1 50 6 6 1 x 1,4 4117 802 220 81,95 ZA07 7.5 1,5 50 6 6 1,5 x 2,6 4117 802 221 82,95 ZA07 7.5 2 50 6 6 2 x 2,6 4117 802 222 82,95 ZA07 10.5 2 50 6 8 2 x 3,7 4117 802 223 85,95 ZA07 10.5 2,5 50 6 8 2,5 x 3,7 4117 802 224 85,95 ZA07 10.5 3 50 6 8 3 x 3,7 4117 802 225 85,95 ZA07 13.5 3 56 10 8 3 x 5 4117 802 226 89,95 ZA07 13.5 4 56 10 8 4 x 5 4117 802 227 89,95 ZA07 16.5 3 56 10 8 3 x 6,5 4117 802 228 97,95 ZA07 16.5 4 56 10 8 4 x 6,5 4117 802 229 97,95 ZA07 16.5 5 56 10 8 5 x 6,5 4117 802 230 97,95 ZA07 19.5 4 63 10 10 4 x 7,5 4117 802 231 115,00 ZA07 19.5 5 63 10 10 5 x 7,5 4117 802 232 115,00 ZA07 19.5 6 63 10 10 6 x 7,5 4117 802 233 115,00 ZA07 22.5 5 63 10 10 5 x 9 4117 802 234 135,00 ZA07 22.5 6 63 10 10 6 x 9 4117 802 235 135,00 ZA07 22.5 8 63 10 10 8 x 9 4117 802 236 135,00 ZA07 25.5 6 63 10 10 6 x 10 4117 802 237 155,00 ZA07 28.5 6 63 10 12 6 x 11 4117 802 238 179,00 ZA07 28.5 8 63 10 12 8 x 11 4117 802 239 179,00 ZA07 28.5 10 71 12 12 10 x 11 4117 802 240 179,00 ZA07 32.5 8 71 12 12 8 x 13 4117 802 241 209,00 ZA07 32.5 10 71 12 12 10 x 13 4117 802 242 209,00 ZA07 45.5 10 71 12 14 10 x 16 4117 802 243 345,00 ZA07 T-groove cutter With cross toothing · HSS-Co · DIN 851 AB · Type N · For milling structural steels, case-hardened steels, and tempered steels, as well as short-chipping non-ferrous metals · Straight shank with pulling face · Right-hand cutting Cutting values, see Table 13 on Page 1/121 P M K N S H K Uncoated k K K K Nominal Ø d1 [mm] Cutting edge L b [mm] Overall L I1 [mm] Shank Ø d2 [mm] No. of cutters For grooves according to DIN 650 [mm] Article no. EUR CK 12.5 6 57 10 6 6 4117 802 035 115,00 ZA07 16 8 62 10 6 8 4117 802 036 129,00 ZA07 18 8 70 12 8 10 4117 802 037 139,00 ZA07 21 9 74 12 8 12 4117 802 038 159,00 ZA07 25 11 82 16 8 14 4117 802 039 189,00 ZA07 28 12 85 16 8 16 4117 802 040 215,00 ZA07 32 14 90 16 8 18 4117 802 041 259,00 ZA07 36 16 103 25 8 20 4117 802 042 335,00 ZA07 40 18 108 25 10 22 4117 802 043 425,00 ZA07
RkJQdWJsaXNoZXIy ODY1MjQ=