D no stock item. Procurement takes place after receipt of order. a = delivery by carrier + = fraction of the PU possible You will find the explanation of the symbols before the index. Cutting tools Machine tap HSS-Co · Shape C · Type VA · Nitrated and steam-tempered · Blue ring · With 40° right twist · Flanks relief-ground · Metric ISO thread · DIN 13 Sheet 1 · Tolerance range ISO2 (6H) · For blind hole threads · For rust-, acid-, and heatresistant steels up to 1,000 N/mm² in strength Nominal thread Ø Pitch [mm] Overall length [mm] Thread L [mm] Shank Ø [mm] Square [mm] Core hole Ø [mm] Article no. EUR CK DIN 371 Nitrated and steam-tempered M3 0,5 56 6,5 3.5 2.7 2,5 4000 867 273 15,95 PU15 M4 0,7 63 8,5 4.5 3.4 3,3 4000 867 274 15,95 PU15 M5 0,8 70 9,5 6 4.9 4,2 4000 867 275 15,95 PU15 M6 1 80 11 6 4.9 5 4000 867 276 16,75 PU15 M8 1,25 90 13,5 8 6.2 6,8 4000 867 278 19,50 PU15 M10 1,5 100 16 10 8 8,5 4000 867 280 23,95 PU15 DIN 376 Nitrated and steam-tempered M12 1,75 110 24 9 7 10,2 4000 867 412 28,95 PU15 M14 2 110 26 11 9 12 4000 867 414 32,95 PU15 M16 2 110 27 12 9 14 4000 867 416 38,95 PU15 M18 2,5 125 30 14 11 15,5 4000 867 418 52,95 PU15 M20 2,5 140 32 16 12 17,5 4000 867 420 60,95 PU15 M22 2,5 140 25 18 14.5 19,5 4000 867 561 85,95 PU15 M24 3 160 30 18 14.5 21 4000 867 562 93,95 PU15 M27 3 160 30 20 16 24 4000 867 563 115,00 PU15 M30 3,5 180 35 22 18 26,5 4000 867 564 155,00 PU15 Recommended use Material Steel N/mm2 Rust-free steel Cast Non-ferrous metal Super alloy Hardened steel Tensile strength <500 <800 <1200 (<HRC38) <1600 (<HRC48) <800 <1200 GG GGG Al wrought alloy Al SI<10 % Cu,Ms TI/Ni/Co <900 900–1500 HRC 48–57 HRC 58–63 4000 867 273 - Vc (m/min) 16 14 5 5 5 16 10 20 12 10 5 3 Cooling Emulsion Emulsion Oil Oil Oil Emulsion Emulsion Emulsion Emulsion Emulsion Oil Oil Machine tap HSS-Co · Shape C · Type VA · TiCN-coated · Blue ring · With 40° right twist · Flanks relief-ground · Metric ISO thread · DIN 13 Sheet 1 · Tolerance range ISO2 (6H) · For blind hole threads · For rust-, acid-, and heat-resistant steels up to 1,000 N/mm² in strength Nominal thread Ø Pitch [mm] Overall length [mm] Thread L [mm] Shank Ø [mm] Square [mm] Core hole Ø [mm] Article no. EUR CK DIN 371 TiCN-coated M3 0,5 56 6,5 3.5 2.7 2,5 4000 867 774 22,95 PU15 M4 0,7 63 8,5 4.5 3.4 3,3 4000 867 775 22,95 PU15 M5 0,8 70 9,5 6 4.9 4,2 4000 867 776 22,95 PU15 M6 1 80 11 6 4.9 5 4000 867 777 22,95 PU15 M8 1,25 90 13,5 8 6.2 6,8 4000 867 778 29,95 PU15 M10 1,5 100 16 10 8 8,5 4000 867 779 35,95 PU15 DIN 376 TiCN-coated M12 1,75 110 24 9 7 10,2 4000 867 396 41,95 PU15 M14 2 110 26 11 9 12 4000 867 397 49,95 PU15 M16 2 110 27 12 9 14 4000 867 398 59,95 PU15 M18 2,5 125 30 14 11 15,5 4000 867 399 83,95 PU15 M20 2,5 140 32 16 12 17,5 4000 867 400 93,95 PU15 Recommended use Material Steel N/mm2 Rust-free steel Cast Non-ferrous metal Super alloy Hardened steel Tensile strength <500 <800 <1200 (<HRC38) <1600 (<HRC48) <800 <1200 GG GGG Al wrought alloy Al SI<10 % Cu,Ms TI/Ni/Co <900 900–1500 HRC 48–57 HRC 58–63 4000 867 774 - Vc (m/min) 16 14 5 5 5 16 10 20 12 10 5 3 Cooling Emulsion Emulsion Oil Oil Oil Emulsion Emulsion Emulsion Emulsion Emulsion Oil Oil 1/80 4000 867 412 4000 867 273 VA HSS-Co vaporisiert P 60° 6H M 4000 867 396 4000 867 774 VA HSS-Co TiCN P 60° 6H M
RkJQdWJsaXNoZXIy ODY1MjQ=