1/72 4000 867 597 4000 867 622 UNI HSS-Co PM HARDLUBE P 60° 6HX M 4000 867 342 4000 867 243 HSSCo P 60° 6H M D no stock item. Procurement takes place after receipt of order. a = delivery by carrier + = fraction of the PU possible You will find the explanation of the symbols before the index. Cutting tools Machine tap PM Advantages: · Maximum protection against wear and exceptionally tough due to the use of HSS-PM · Optimal chip removal up to 3xdm thanks to optimised groove geometry (shape B) · Optimal chip removal up to 3xdm thanks to high angle of twist 50° (shape C) · Reduced surface friction due to multi-layer coating · Low tool costs thanks to universal application HARDBLUE-coated for universal application in VA steel, tempered steel, hardened steel, tool steel, structural steel, aluminium and copper alloys and cast Machine tap HSS-Co PM · Shape B · Type UNIVERSAL · HARDLUBE coated · Straight-fluted · Flanks relief-ground · Metric ISO thread · DIN 13 Sheet 1 · Tolerance range 6HX · With spiral point for through-hole threads Universal application! Nominal thread Ø Pitch [mm] Overall length [mm] Thread L [mm] Shank Ø [mm] Square [mm] Core hole Ø [mm] Article no. EUR CK DIN 371 HARDLUBE coated M2 0,4 45 8 2.8 2.1 1,6 4000 867 622 34,95 PU15 M2,5 0,45 50 9 2.8 2.1 2,05 4000 867 623 33,95 PU15 M3 0,5 56 11 3.5 2.7 2,5 4000 867 591 27,95 PU15 M4 0,7 63 13 4.5 3.4 3,3 4000 867 592 28,95 PU15 M5 0,8 70 16 6 4.9 4,2 4000 867 593 29,95 PU15 M6 1 80 19 6 4.9 5 4000 867 594 29,95 PU15 M8 1,25 90 22 8 6.2 6,8 4000 867 595 38,95 PU15 M10 1,5 100 24 10 8 8,5 4000 867 596 48,95 PU15 DIN 376 HARDLUBE coated M12 1,75 110 28 9 7 10,2 4000 867 597 61,95 PU15 M16 2 110 32 12 9 14 4000 867 598 115,00 PU15 M20 2,5 140 34 16 12 17,5 4000 867 599 189,00 PU15 M24 3 160 38 18 14.5 21 4000 867 406 215,00 PU15 M27 3 160 38 20 16 24 4000 867 407 279,00 PU15 M30 3,5 180 45 22 18 26,5 4000 867 408 289,00 PU15 Recommended use Material Steel N/mm2 Rust-free steel Cast Non-ferrous metal Super alloy Hardened steel Tensile strength <500 <800 <1200 (<HRC38) <1600 (<HRC48) <800 <1200 GG GGG Al wrought alloy Al SI<10 % Cu,Ms TI/Ni/Co <900 900–1500 HRC 48–57 HRC 58–63 4000 867 622 - Vc (m/min) 28 23 16 12 15 12 24 20 50 30 20 Cooling Emulsion/ oil Emulsion/ oil Emulsion/ oil Emulsion/ oil Emulsion/ oil Emulsion/ oil Emulsion/ oil Emulsion/ oil Emulsion/ oil Emulsion/ oil Emulsion/ oil For more information see page 1/72 Machine tap HSS-Co · Shape B · Straight-fluted · Flanks relief-ground · Metric ISO thread · DIN 13 Sheet 1 · Tolerance range ISO2 (6H) · With spiral point for through-hole threads · For steels up to approx. 900 N/mm² in strength Nominal thread Ø Pitch [mm] Overall length [mm] Thread L [mm] Shank Ø [mm] Square [mm] Core hole Ø [mm] Article no. EUR CK DIN 371 M3 0,5 56 9 3.5 2.7 2,5 4000 867 243 10,25 PU15 M4 0,7 63 12 4.5 3.4 3,3 4000 867 244 10,25 PU15 M5 0,8 70 13 6 4.9 4,2 4000 867 245 10,25 PU15 M6 1 80 15 6 4.9 5 4000 867 246 10,25 PU15 M8 1,25 90 18 8 6.2 6,8 4000 867 248 11,75 PU15 M10 1,5 100 20 10 8 8,5 4000 867 250 13,75 PU15 DIN 376 M12 1,75 110 23 9 7 10,2 4000 867 342 16,75 PU15 M14 2 110 25 11 9 12 4000 867 344 21,95 PU15 M16 2 110 25 12 9 14 4000 867 346 23,95 PU15 M18 2,5 125 30 14 11 15,5 4000 867 348 31,95 PU15 M20 2,5 140 30 16 12 17,5 4000 867 350 37,95 PU15 M22 2,5 140 30 18 14.5 19,5 4000 867 340 62,95 PU15 M24 3 160 36 18 14.5 21 4000 867 341 58,95 PU15 M27 3 160 36 20 16 24 4000 867 291 76,95 PU15 M30 3,5 180 40 22 18 26,5 4000 867 292 98,95 PU15 Recommended use Material Steel N/mm2 Rust-free steel Cast Non-ferrous metal Super alloy Hardened steel Tensile strength <500 <800 <1200 (<HRC38) <1600 (<HRC48) <800 <1200 GG GGG Al wrought alloy Al SI<10 % Cu,Ms TI/Ni/Co <900 900–1500 HRC 48–57 HRC 58–63 4000 867 243 - Vc (m/min) 10 8 23 20 Cooling Emulsion/ oil Emulsion/ oil Emulsion/ oil Emulsion/ oil
RkJQdWJsaXNoZXIy ODY1MjQ=