1/46 60° DIN 334-C HSS 75° HSS 120° HSS D no stock item. Procurement takes place after receipt of order. a = delivery by carrier + = fraction of the PU possible You will find the explanation of the symbols before the index. Cutting tools Countersink HSS · DIN 334 C · 3 cutters · Countersink angle 60° · Straight shank · Right-hand cutting · Ideal for burr-free and chatter-free countersinking, deburring, and countersinking in steel and cast iron as well as non-ferrous and light metals · Best results at low cutting speed Nominal Ø [mm] Small Ø [mm] Shank Ø [mm] Overall length [mm] Steel < 500 N f [mm/ rev] Article no. Uncoated EUR CK Nominal Ø [mm] Small Ø [mm] Shank Ø [mm] Overall length [mm] Steel < 500 N f [mm/ rev] Article no. Uncoated EUR CK 6.3 1.6 5 45 0,09 4000 865 124 9,75 PE11 16 4 10 63 0,14 4000 865 128 16,25 PE11 8 2 6 50 0,09 4000 865 125 10,25 PE11 20 5 10 67 0,2 4000 865 129 22,95 PE11 10 2.5 6 50 0,12 4000 865 126 12,50 PE11 25 6.3 10 71 0,2 4000 865 130 31,95 PE11 12.5 3.2 8 56 0,14 4000 865 127 13,25 PE11 Recommended use Material Steel N/mm2 Rust-free steel Cast Non-ferrous metal Super alloy Hardened steel Tensile strength <500 <800 <1200 (<HRC38) <1600 (<HRC48) <800 <1200 GG GGG Al wrought alloy Al SI<10 % Cu,Ms TI/Ni/Co <900 900–1500 HRC 48–57 HRC 58–63 4000 865 124 - Vc (m/min) 30 28 35 35 Cooling Emulsion Emulsion Emulsion Emulsion Countersink HSS · Shape C · 3 cutters · Countersink angle 75° · Straight shank · Right-hand cutting · Ideal for burr-free and chatter-free countersinking, deburring, and countersinking in steel and cast iron as well as non-ferrous and light metals · Best results at low cutting speed Nominal Ø [mm] Small Ø [mm] Shank Ø [mm] Overall length [mm] Steel < 500 N f [mm/ rev] Article no. Uncoated EUR CK Nominal Ø [mm] Small Ø [mm] Shank Ø [mm] Overall length [mm] Steel < 500 N f [mm/ rev] Article no. Uncoated EUR CK 6.3 1.6 5 45 0,09 4000 865 131 13,25 PE11 16.5 4 10 63 0,14 4000 865 135 21,95 PE11 8.3 2 6 50 0,09 4000 865 132 13,50 PE11 20.5 5 10 67 0,16 4000 865 136 32,95 PE11 10.4 2.5 6 50 0,12 4000 865 133 16,50 PE11 25 6.3 10 71 0,2 4000 865 137 42,95 PE11 12.4 3.2 8 56 0,14 4000 865 134 16,95 PE11 Recommended use Material Steel N/mm2 Rust-free steel Cast Non-ferrous metal Super alloy Hardened steel Tensile strength <500 <800 <1200 (<HRC38) <1600 (<HRC48) <800 <1200 GG GGG Al wrought alloy Al SI<10 % Cu,Ms TI/Ni/Co <900 900–1500 HRC 48–57 HRC 58–63 4000 865 131 - Vc (m/min) 30 28 35 35 Cooling Emulsion Emulsion Emulsion Emulsion Countersink HSS · Shape C · 3 cutters · Countersink angle 120° · Straight shank · Right-hand cutting · Ideal for burr-free and chatter-free countersinking, deburring, and countersinking in steel and cast iron as well as non-ferrous and light metals · Best results at low cutting speed Nominal Ø [mm] Small Ø [mm] Shank Ø [mm] Overall length [mm] Steel < 500 N f [mm/ rev] Article no. Uncoated EUR CK Nominal Ø [mm] Small Ø [mm] Shank Ø [mm] Overall length [mm] Steel < 500 N f [mm/ rev] Article no. Uncoated EUR CK 6.3 1.5 5 45 0,09 4000 865 138 13,25 PE11 16.5 3.5 10 63 0,14 4000 865 142 21,95 PE11 8.3 2 6 50 0,09 4000 865 139 13,50 PE11 20.5 4 10 67 0,2 4000 865 143 32,95 PE11 10.4 2.5 6 50 0,12 4000 865 140 16,50 PE11 25 5 10 71 0,2 4000 865 144 42,95 PE11 12.4 3 8 56 0,14 4000 865 141 16,95 PE11 Recommended use Material Steel N/mm2 Rust-free steel Cast Non-ferrous metal Super alloy Hardened steel Tensile strength <500 <800 <1200 (<HRC38) <1600 (<HRC48) <800 <1200 GG GGG Al wrought alloy Al SI<10 % Cu,Ms TI/Ni/Co <900 900–1500 HRC 48–57 HRC 58–63 4000 865 138 - Vc (m/min) 30 28 35 35 Cooling Emulsion Emulsion Emulsion Emulsion
RkJQdWJsaXNoZXIy ODY1MjQ=