1/45 90° DIN 335-C HSS 90° VA DIN 335-C HSS ASP 90° DIN 335-C HM Countersink HSS · DIN 335 C · With extended shank · 3 cutters · Countersink angle 90° · Straight shank · For countersinking and deburring holes in steel, cast iron, and non-ferrous metals · The 3 cutters afford a chatter-free cut Nominal Ø [mm] Small Ø [mm] Shank Ø [mm] Overall length [mm] Steel < 500 N f [mm/ rev] Article no. Uncoated EUR CK Nominal Ø [mm] Small Ø [mm] Shank Ø [mm] Overall length [mm] Steel < 500 N f [mm/ rev] Article no. Uncoated EUR CK 6.3 1.5 5 85 0,09 4000 865 396 22,95 PE11 16.5 3.2 10 112 0,14 4000 865 393 27,95 PE11 8.3 2 6 85 0,09 4000 865 397 22,95 PE11 20.5 3.5 10 115 0,2 4000 865 394 33,95 PE11 10.4 2.5 6 88 0,12 4000 865 391 22,95 PE11 25 3.8 10 118 0,2 4000 865 395 48,95 PE11 12.4 2.8 8 108 0,14 4000 865 392 22,95 PE11 Recommended use Material Steel N/mm2 Rust-free steel Cast Non-ferrous metal Super alloy Hardened steel Tensile strength <500 <800 <1200 (<HRC38) <1600 (<HRC48) <800 <1200 GG GGG Al wrought alloy Al SI<10 % Cu,Ms TI/Ni/Co <900 900–1500 HRC 48–57 HRC 58–63 4000 865 396 - Vc (m/min) 30 28 35 35 Cooling Emulsion Emulsion Emulsion Emulsion Unless otherwise stated, delivery without content/ accessories. The offers are only valid for commercial customers. All prices excluding VAT. Cutting tools Countersink Powder steel · ASP · DIN 335 C · For VA steels and non-ferrous metals · 3 cutters · Countersink angle 90° · Straight shank · For countersinking and deburring bores ASP Countersink drill bit sand deburrer made of powder metallurgical high-speed steel · Unlike conventional HSS steels, metallurgically produced steels have a uniform, fine-grained material structure · They therefore have a good warm hardness, compressive strength, and wear resistance · Ideal for VA steels, rust-, and acid- resistant steels as well as titanium and titanium alloys Nominal Ø [mm] Small Ø [mm] Shank Ø [mm] Overall length [mm] Steel < 500 N f [mm/ rev] Article no. Uncoated EUR CK Nominal Ø [mm] Small Ø [mm] Shank Ø [mm] Overall length [mm] Steel < 500 N f [mm/ rev] Article no. Uncoated EUR CK 6.3 1.5 5 45 0,09 4000 865 020 26,95 PE11 16.5 3.2 10 60 0,14 4000 865 028 48,95 PE11 8.3 2 6 50 0,09 4000 865 022 31,95 PE11 20.5 3.5 10 63 0,2 4000 865 030 66,95 PE11 10.4 2.5 6 50 0,12 4000 865 024 31,95 PE11 25 3.8 10 67 0,2 4000 865 032 92,95 PE11 12.4 2.8 8 56 0,14 4000 865 026 41,95 PE11 31 4.2 12 71 0,22 4000 865 034 135,00 PE11 Recommended use Material Steel N/mm2 Rust-free steel Cast Non-ferrous metal Super alloy Hardened steel Tensile strength <500 <800 <1200 (<HRC38) <1600 (<HRC48) <800 <1200 GG GGG Al wrought alloy Al SI<10 % Cu,Ms TI/Ni/Co <900 900–1500 HRC 48–57 HRC 58–63 4000 865 020 - Vc (m/min) 38 35 30 20 15 12 20 18 10 12 Cooling Emulsion Emulsion Emulsion Cutting oil Cutting oil Cutting oil Emulsion Emulsion Cutting oil Cutting oil Countersink DIN 335 C · 3 cutters · Countersink angle 90° · Straight shank · Right-hand cutting · For burr-free and chatter-free countersinking, deburring and sinking · Best results at low cutting speed HSS: For processing aluminium HM: Ideal in case of abrasive and hard steels over 1,000 N/mm² strength, GG over 240 HB Nominal Ø [mm] Small Ø [mm] Shank Ø [mm] Overall length [mm] Steel < 500 N f [mm/rev] Article no. EUR CK 6.3 1.5 5 45 0,09 4000 601 473 125,00 ZV08 8.3 2 6 50 0,09 4000 601 474 139,00 ZV08 10.4 2.5 6 50 0,12 4000 601 475 149,00 ZV08 12.4 2.8 8 56 0,14 4000 601 476 165,00 ZV08 16.5 3.2 10 60 0,14 4000 601 477 185,00 ZV08 20.5 3.5 10 63 0,2 4000 601 478 239,00 ZV08 25 3.8 10 67 0,2 4000 601 479 329,00 ZV08 31 4.2 12 71 0,22 4000 601 480 415,00 ZV08 Recommended use Material Steel N/mm2 Rust-free steel Cast Non-ferrous metal Super alloy Hardened steel Tensile strength <500 <800 <1200 (<HRC38) <1600 (<HRC48) <800 <1200 GG GGG Al wrought alloy Al SI<10 % Cu,Ms TI/Ni/Co <900 900–1500 HRC 48–57 HRC 58–63 4000 601 464 - Vc (m/min) 25 40 40 4000 601 473 - Vc (m/min) 60 60 45 30 24 20 45 35 180 80 180 18 16 8 6 Cooling Emulsion Emulsion Emulsion Cutting oil Cutting oil Cutting oil Emulsion Emulsion Emulsion Emulsion Cutting oil Cutting oil extra long
RkJQdWJsaXNoZXIy ODY1MjQ=