1/42 4000 865 189 4000 865 151 90° DIN 335-C HSSTiN HSS 4000 865 222 4000 865 000 90° VA DIN 335-C HSSTiAIN HSSCo D no stock item. Procurement takes place after receipt of order. a = delivery by carrier + = fraction of the PU possible You will find the explanation of the symbols before the index. Cutting tools Countersink HSS · DIN 335 C · 3 cutters · Countersink angle 90° · Straight shank · For countersinking and deburring holes in steel, cast iron, and non-ferrous metals · The three blades afford a chatter-free cut Nominal Ø [mm] Small Ø [mm] Shank Ø [mm] Overall length [mm] Steel < 500 N f [mm/rev] Article no. HSS - Uncoated EUR CK Article no. HSS - TiN-coated EUR CK 4.3 1.3 4 40 0,07 4000 865 151 7,75 PE11 4000 865 189 11,75 PE11 5 1.5 4 40 0,07 4000 865 152 7,75 PE11 - - - 6 1.5 5 45 0,09 4000 865 155 7,75 PE11 - - - 6.3 1.5 5 45 0,09 4000 865 156 7,75 PE11 4000 865 190 13,75 PE11 7 1.8 6 50 0,09 4000 865 157 8,25 PE11 - - - 8 2 6 50 0,09 4000 865 159 8,25 PE11 - - - 8.3 2 6 50 0,09 4000 865 160 8,25 PE11 4000 865 191 14,95 PE11 10 2.5 6 50 0,12 4000 865 162 8,75 PE11 4000 865 192 14,50 PE11 10.4 2.5 6 50 0,12 4000 865 163 8,75 PE11 4000 865 193 14,50 PE11 11.5 2.8 8 56 0,14 4000 865 164 9,95 PE11 - - - 12.4 2.8 8 56 0,14 4000 865 165 9,95 PE11 4000 865 195 15,95 PE11 15 3.2 10 60 0,14 4000 865 167 11,95 PE11 - - - 16.5 3.2 10 60 0,14 4000 865 168 11,95 PE11 4000 865 198 19,95 PE11 19 3.5 10 63 0,14 4000 865 169 16,25 PE11 - - - 20.5 3.5 10 63 0,16 4000 865 170 16,25 PE11 - - - 20.5 3.5 10 63 0,2 - - - 4000 865 200 26,95 PE11 23 3.8 10 67 0,16 4000 865 171 19,75 PE11 - - - 25 3.8 10 67 0,2 4000 865 172 20,95 PE11 4000 865 202 34,95 PE11 31 4.2 12 71 0,22 4000 865 174 25,95 PE11 4000 865 204 44,95 PE11 Recommended use Material Steel N/mm2 Rust-free steel Cast Non-ferrous metal Super alloy Hardened steel Tensile strength <500 <800 <1200 (<HRC38) <1600 (<HRC48) <800 <1200 GG GGG Al wrought alloy Al SI<10 % Cu,Ms TI/Ni/Co <900 900–1500 HRC 48–57 HRC 58–63 4000 865 151 - Vc (m/min) 30 28 35 35 4000 865 189 - Vc (m/min) 32 30 9 35 70 Cooling Emulsion Emulsion Emulsion Cutting oil Cutting oil Cutting oil Emulsion Emulsion Emulsion Emulsion Cutting oil Cutting oil Countersink DIN 335 C · 3 cutters · Countersink angle 90° · Straight shank · For countersinking and deburring holes in steel, cast iron, and non-ferrous metals · The three blades afford a chatter-free cut HSS: For steel, cast iron, and non-ferrous metals HSS-Co: For steel, cast, non-ferrous metals and rust- and heat-resistant steels Nominal Ø [mm] Small Ø [mm] Shank Ø [mm] Overall length [mm] Steel < 500 N f [mm/rev] Article no. HSS-Co - Uncoated EUR CK Article no. HSS - TiAINcoated EUR CK 6.3 1.5 5 45 0,09 4000 865 000 10,95 PE11 4000 865 222 12,95 PE11 8.3 2 6 50 0,09 4000 865 002 13,25 PE11 4000 865 223 15,25 PE11 10.4 2.5 6 50 0,12 4000 865 004 14,95 PE11 4000 865 224 16,50 PE11 12.4 2.8 8 56 0,14 4000 865 006 16,50 PE11 4000 865 225 20,95 PE11 15 3.2 10 60 0,14 4000 865 008 18,25 PE11 - - - 16.5 3.2 10 60 0,14 4000 865 010 20,95 PE11 4000 865 226 21,95 PE11 20.5 3.5 10 63 0,2 4000 865 012 28,95 PE11 4000 865 227 25,95 PE11 25 3.8 10 67 0,2 4000 865 014 33,95 PE11 4000 865 228 33,95 PE11 31 4.2 12 71 0,22 4000 865 016 54,95 PE11 4000 865 229 44,95 PE11 Recommended use Material Steel N/mm2 Rust-free steel Cast Non-ferrous metal Super alloy Hardened steel Tensile strength <500 <800 <1200 (<HRC38) <1600 (<HRC48) <800 <1200 GG GGG Al wrought alloy Al SI<10 % Cu,Ms TI/Ni/Co <900 900–1500 HRC 48–57 HRC 58–63 4000 865 000 - Vc (m/min) 30 28 8 4 7 7 15 15 35 60 7 6 4000 865 222 - Vc (m/min) Cooling Emulsion Emulsion Emulsion Cutting oil Cutting oil Cutting oil Compressed air Compressed air Emulsion Emulsion Cutting oil Cutting oil
RkJQdWJsaXNoZXIy ODY1MjQ=